Xantrex Link 2000 Manuel d'utilisateur télécharger pdf (Page 11)

F02 - BATTERY TYPE

0 = LIQUID CELL (DEFAULT) 1 = GEL CELL (STANDARD)

2 = GEL CELL (FAST CHARGE) 3 = AGM (Absorbed Glass Mat)

This function (Default: Type 0, standard liquid cells) sets the appropriate charge

and float voltages for the FREEDOM charger (see table below) and sets an appropriate

Peukert exponent. Gel cell owners may use Type 1 or Type 2, but should consult with

the battery manufacturer prior to using the more aggressive charging regimen described

by Type 2. Type 3 sets Acceptance and Float voltages suited to AGM type batteries.

F03 -

VIEW OR SET AMBIENT BATTERY TEMPERATURE

THIS FUNCTION DEPENDS ON THE SETTING OF F14 (SEE PAGE 14

)

IF F14 IS

ON, F03 VIEWS THE PRESENT BATTERY TEMP. (°F)

If F14 is ON, charging voltage of the Freedom charger and the Ideal Regulator (if

using a Link 2000-R) is based on the TEMPERATURE COMPENSATION TABLE

below. The temperature is displayed until another button is pressed on the Link.

IF F14 IS OFF, F03 SETS A DECLARED BATTERY TEMP. (°F)

DEFAULT = 70 °F RANGE = 30–120 °F STEP = 10 °F

The default value for ambient temperature is 70 °F. The ambient temperature of the

battery may be set up to select the appropriate Charge and Float Voltages for the charger.

The temperature may be selected in 10 °F increments. The setup procedure is the same

as previously described.

Setting up a different value should only be done if the battery is at a temperature

significantly different from 70 °F

when they are being charged from the FREEDOM.

If the batteries are located in a hot engine room, but are not normally charged from the

FREEDOM when the engine is running, do not adjust the temperature to the engine

room level. High temperatures are destructive to batteries. If your batteries are regularly

subjected to temperatures above 100 °F you should relocate them or supply forced fresh

air ventilation.

Caution! Do not adjust to extremes unless the battery is normally at that

temperature. Destructive over- or under-charging may occur. Multiply values by

2 for 24-volt systems. Voltages are typical, charger regulation

+ 0.2 volts DC.

TEMPERATURE COMPENSATION TABLE

TEMP TYPE 0 TYPE 1 TYPE 2 TYPE 3

Liquid Gel 1 (Std) Gel 2 (Fast) AGM

°F °C ACCEPT FLOAT ACCEPT FLOAT ACCEPT FLOAT ACCEPT FLOAT

120 49 12.5 12.5 13.0 13.0 13.0 13.0 12.9 12.9

110 43 13.6 12.7 13.5 13.0 14.0 13.4 13.9 12.9

100 38 13.8 12.9 13.7 13.2 14.1 13.5 14.0 13.0

90 32 14.0 13.1 13.8 13.3 14.2 13.6 14.1 13.1

80 27 14.2 13.3 14.0 13.5 14.3 13.7 14.2 13.2

70 21 14.4 13.5 14.1 13.6 14.4 13.8 14.3 13.3

60 16 14.6 13.7 14.3 13.8 14.5 13.9 14.4 13.4

50 10 14.8 13.9 14.4 13.9 14.6 14.0 14.5 13.5

40 5 15.0 14.1 14.6 14.1 14.7 14.1 14.6 13.6

30 -1 15.2 14.3 14.7 14.2 14.8 14.2 14.7 13.7

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 42 43

Commentaires sur ces manuels

Pas de commentaire

Xantrex Link 2000 Manuel d'utilisateur Page 11

Commentaires sur ces manuels

Produits connexes et manuels pour Non Xantrex Link 2000